110 Cold Galv: A single pack epoxy ester based zinc rich primer
offering outstanding corrosion resistance and protection for steel as a single coat or as the
primer in a multi coat finish. The high zinc content provides cathodic protection in a
sacrificial manner to prevent spread of corrosion in the event of minor damage.
116 Nylocote: 116 Nylocote is a two part, cold cure, epoxy
polyamide finish exhibiting outstanding adhesion to most material with excellent resistance
against corrosive conditions such as atmospheric fumes or spillage and water immersion.
130 Water Based Epoxy Floor Coating:Forminex Water based Epoxy
Floor Coating is a two-pack, water based epoxy finish for most types of floor including concrete,
timber and fibre cement. It can also be used as a coating for most types of vinyl and lino
floor covering. Being water based it offers 2 major advantages over older solvent based epoxy
floor finishes; low odour and low VOC, tolerant of green or damp concrete.
340 Chlorinated Rubber Pool Paint:Forminex Chlorinated Rubber
Pool Paint is a single pack paint designed for use pools previously painted with Chlorinated
Rubber. It is not suitable over 2 pack epoxy or 2 pack polyurethane paints.
392 Anticorrosive Vinyl Mastic:Single pack mastic designed
for protection of immersed surfaces (steel/plywood). 392 Anticorrosive Vinyl Mastic offers
excellent flexibility and moisture resistance. 392 Anticorrosive Vinyl Mastic also has
excellent seawater immersion resistance. It has excellent compatibility with vinyl tar,
bituminous anti-corrosive and chlorinated rubber system and with broad range of anti-fouling.
639 E3 Primer: Forminex E3 Primer is a 2 part epoxy resin based
primer coat ideally suitable for use on ferrous and non-ferrous metal substances. E3 has been
formulated to the requirements of Title 21 CFR FDA (US Federal Government) thus making it
suitable for use in Food Contact applications as a coating.
643 Ceramaglass: Ceramaglass is a single pack, clear, adhesion
promoting, fast drying primer. Ceramaglass can be used on glass, ceramic tiles, porcelain,
terrazzo, some plastics, laminates, vinyl & lino and vitreous enamel.
650 Formatt: 650 Formatt is a finely powdered, high efficiency
matting agent. Due to its unique manufacturing process it is particularly suitable for systems
which are difficult to matt and for both clear and pigmented finish coatings.
655 Marine Varnish: 655 Marine Varnish is a single pack, oil-urethane
varnish; available in either clear or timber shades and contains light– fast ultra-violet diffusing
pigments with excellent weathering properties. 655 Marine Varnish provides a flexible, hardwearing
surface that is exceptionally resistant to weather, salt water & spray, chemicals, petrol and oil.
656 Epoxy Pool Paint: 656 Epoxy Pool Paint is a polyamide
cured 2-Pack epoxy coating. It has excellent resistance to pool chemicals, abrasion, and
attack from algae and provides a smooth, easy to clean finish.
660 Epoxy Undercoat (1K): 660 Epoxy Undercoat is a single-pack,
epoxy-ester marine grade primer and undercoat. It has excellent resistance to salt, chemicals,
alkali and abrasion. It is highly flexible and has excellent anticorrosive properties when
applied to metals. Dries to a smooth matt finish providing an excellent base for over coating.
661 Fairing Filling Powder: 661 Fairing Filler Powder is a
formulated mineral and microsphere powder blend which has been specially treated to improve
it’s miscibility with resins and provides easy sanding properties while still giving good
vertical hold. It can be mixed with Epoxy Resins to thicken them for use as a light-weight
full strength filler or as a “Fairing” blend. The mixed product is suitable for producing
high strength coves, filling nail and screw holes and fairing hulls (both above and below
the waterline) on all suitably prepared marine craft.
662 FX Hardener Part B: 662 Fx Hardener is a formulated
hardener for all Forminex Two Pack polyurethane undercoats, primers and interior clears
and top coats.
663 NY Hardener Part B: 663 NY Hardener is a non yellowing
hardener for interior and exterior use. For use with Forminex top coats and non yellowing
664 Sanding Primer: 664 Sanding Primer is a high build,
easily sanded primer / undercoat, especially formulated to achieve a high-build surface
that has good filling properties. It is suitable for marine and general applications.
665 Epoxy Timber Preserver: 665 Epoxy Timber Preserver is an
excellent barrier coating for all marine and general situations. 665 Epoxy Timber Preserver
also has uses on other absorbent substrates such as concrete.
666 Vinyl Primer: 666 Vinyl Primer (in older literature also
known as Marine Systems or Forminex Anti Fouling Primer) is a single pack solvent based primer.
It has excellent bleed stopping properties and provides superior adhesion to a wide range of
substrates including: wood, steel, masonry and fibreglass. 666 Vinyl Primer may be used on
surfaces that will remain immersed in water.
675 Paint Stripper: 675 Paint Stripper was developed to remove
the most difficult to remove coatings i.e. two-pack polyurethane’s and epoxies, it is therefore
very effective for the removal of almost any paint coating or varnish. It is recommended for
use on wood, concrete and metal surfaces where the minimum of effort with the maximum
efficiency is required. NOTE: Not suitable for use over fibreglass (GRP) or aluminium surfaces.
It is fast acting; non-flammable; will not stain or damage timber; leaves surfaces ready for
re-coating; does not require neutralizing, and does not contain wax.
677 Supergloss: 677 Supergloss is a marine grade non-yellowing
linear (aliphatic) Polyurethane surface coating for outdoor and indoor use.
678 Universal Undercoat: 678 Universal Undercoat is a two-pack
Polyurethane based, pigmented undercoat designed for use on surfaces such as timber, fiberglass
hardboards, fibrous cement, concrete etc., Also suitable on primed surfaces such as Aluminum
or Steel. For superior adhesion over difficult to paint surfaces See Data Sheet for 643 Ceramaglass.
680 Epoxy Enamel: 680 Epoxy Enamel is a single-pack, epoxy-ester
marine grade enamel. It has excellent resistance to salt, chemicals, alkali and abrasion. It is
highly flexible and has excellent anticorrosive properties when applied to metals.
681 Red Metal Primer: 681 Red Metal Primer is a Polyurethane
based Metal Primer which combines adhesion with great impermeability and which incorporates
corrosion resistant pigments.
682 Epoxy Glue: 682 Epoxy Glue is a superior non-shrink two
component high viscosity gel adhesive especially designed for use in adverse conditions. It
is supplied in a handy 1:1 mix ratio in a range of pack sizes.
684 Superwash: 684 Superwash is a water based, biodegradable,
industrial strength, multipurpose cleaning detergent suitable for the preparation of swimming
pool surfaces and floors prior to painting. 684 Superwash is non-flammable and has virtually
no odour making it suitable for use in confined areas.
688 Formacoat: Formacoat is a single-pack, solvent based acrylic
re-coatable topcoat. It has excellent resistance to water, salt, chemicals and alkali. It is
highly flexible and abrasion resistant.
689 E2 Primer: Forminex E2 Primer is a 2 part epoxy resin based
primer coat ideally suitable for use on all ferrous and non-ferrous metal substances.
690 Epoxy LV Sheathing Resin: Forminex Low Viscosity 4:1 Epoxy Resin is a two-pack epoxy resin for
laminating and sheathing. It may also be modified to become an adhesive or filler/putty (See instructions below). It has been developed to provide
superior wet out and cured characteristics at ambient temperatures. The low mixed viscosity assists good penetration and wet out.
693 Epoxy Glue Powder: Epoxy Glue Adhesive Powder is a
carefully formulated mineral & fibre powder blend, which can be mixed with the Marine Systems
epoxy sheathing systems to thicken it & allow its use as a high density, full strength glue.
699 Epoxy Casting Resin (2:1 Mix ): 699 Epoxy Casting Resin is a crystal clear two-pack epoxy. It is
most commonly used as a high build clear finish that dries to a hard glossy finish. Being solvent free it sets without shrinkage for laminating and
sheathing and is low odour.
768 Vitraform AQ: 768 Vitraform AQ is an innovative new water
based non yellowing, flexible, 2-Part clear fluro-acrylic coating. Originally formulated as
an anti-graffiti coating, its excellent resistance to abrasion, chemicals, solvents and oils
also makes it suitable for a wide range of other applications.
858 Epoline Primer: A two pack epoxy-polyamide based primer
surfacer. 858 Epoline Primer is an excellent anticorrosive coating possessing excellent
adhesion to metal together with outstanding flexibility, chemical and water resistance.
858 Epoline Primer has also been formulated to give excellent build and sanding properties
when used on timber, particle board, MDF board and similar substrates.
859 Estagloss: A two pack non yellowing polyurethane enamel
exhibiting outstanding gloss, colour retention and exterior durability coupled with a high
degree of chemical, solvent and abrasion resistance. On properly prepared surfaces, the
performance of this material is far beyond that obtained by any conventional coating system.